Welcome! Here are the website rules, as well as some tips for using this forum.
Need to contact us? Visit https://heatinghelp.com/contact-us/.
Click here to Find a Contractor in your area.
If our community has helped you, please consider making a contribution to support this website. Thanks!
Best Of
Re: Gas Grille outside, gas connector???
@ChrisJ as far as stoves connected in the back you screw a nipple and a 90 onto the stove and drill a hole in the floor. Push the stove into position so that the 90 lines up with the hole in the floor. Then screw a nipple up through the floor into the 90. Gas cock and union in the basement.
You only have to run up and down the stairs 10 time to get this made up.
MA does allow flex connectors now and did before but there was a period of time in between maybe 25-30 years ago where everything was hard piped.
They also outlawed CSST for a while but let it back in
Unless you never worked in MA you wouldn't believe the problems.
the latest thing is high pressure gas. If an existing system is HP with screwed pipe that was always legal but now is not watch out trying to change any equipment or any alterations. Up to the gas co discretion they can make you rip it all out.
Also (and this one really twists me up) you can do a job that meets code and the inspector approves it. If the gas company doesn't like it...they have the last word, not the inspectors, not the state board
You only have to run up and down the stairs 10 time to get this made up.
MA does allow flex connectors now and did before but there was a period of time in between maybe 25-30 years ago where everything was hard piped.
They also outlawed CSST for a while but let it back in
Unless you never worked in MA you wouldn't believe the problems.
the latest thing is high pressure gas. If an existing system is HP with screwed pipe that was always legal but now is not watch out trying to change any equipment or any alterations. Up to the gas co discretion they can make you rip it all out.
Also (and this one really twists me up) you can do a job that meets code and the inspector approves it. If the gas company doesn't like it...they have the last word, not the inspectors, not the state board
Re: What is it ?
It looks like a paper gasket that someone was trying to use to seal up the matched faces of a union, and it obviously didn't work well...
ME
ME
https://www.youtube.com/watch?v=vffdymvjluk
Re: Best and acceptable media's for radiant heat for OUTDOOR applications.
Styrofoam under tubing......I've heard ants and termites like to burrow in it. Maybe lay down some insecticide first, but being in VT I assume your on well water so that may be a problem.
Overall I wonder about just sleaving the driveway tubing, so if it leaks in future you can just dig up the edges and pull in new tubing. Will have a cost of lower conductivity from water to soil though, air gap.
I bigger question is why look for a place to dump the excess heat, just figure out a way to throttle down the boiler. Dumping excess heat will just cost you fuel and labor feeding the boiler.
Overall I wonder about just sleaving the driveway tubing, so if it leaks in future you can just dig up the edges and pull in new tubing. Will have a cost of lower conductivity from water to soil though, air gap.
I bigger question is why look for a place to dump the excess heat, just figure out a way to throttle down the boiler. Dumping excess heat will just cost you fuel and labor feeding the boiler.
Leonard
1
Re: Best and acceptable media's for radiant heat for OUTDOOR applications.
I doubt you will have much over 150,000 BTU/hr output from that boiler. They typically run around 40-45% efficiencies. That is full fired with dry hardwood
Keep you output expectations reasonable and about a dozen cords of wood on hand
Keep you output expectations reasonable and about a dozen cords of wood on hand
hot_rod
0
Re: Low water cut off malfuntions
@Jamie Hall said"This is not optional maintenance."
Unfortunately steam systems (all heating systems really) require maintenance to work safely and to have any reliability and longevity. Failure to do this results in major problems. Just like a car. Cars won't run long without oil, boilers need water. Low water cutoffs need at the least yearly maintenance
Unfortunately steam systems (all heating systems really) require maintenance to work safely and to have any reliability and longevity. Failure to do this results in major problems. Just like a car. Cars won't run long without oil, boilers need water. Low water cutoffs need at the least yearly maintenance
EBEBRATT-Ed
-1
Re: Burner keeps locking out..tried several things .. what to try next?
Here we go again. How many of these oil line issues have we had lately??
Another suction leak! The technicians you have obviously can't find the leak. You have a suction leak, find it and fix it and your problems are over.
Overhead line if it was me I would change it to two pipe or you can try a Tiger loop
Where are the technicians who can flare tubing and get a line tight?
I admit on threaded fittings leaks are more common since Teflon tape has been prohibited
Another suction leak! The technicians you have obviously can't find the leak. You have a suction leak, find it and fix it and your problems are over.
Overhead line if it was me I would change it to two pipe or you can try a Tiger loop
Where are the technicians who can flare tubing and get a line tight?
I admit on threaded fittings leaks are more common since Teflon tape has been prohibited
Re: Mod CON? Or Power vent 85%?
@Gordy Not sure if you're talking about me when you say "what gets me is that some say I'll only save 100 dollars a year. Now think of it collectively city wide, state wide, country, world wide. That's not peanuts. Every little bit adds up to huge energy savings in the big picture."
Sure, it adds up when a few million people do it, but those other people aren't responsible for putting food on my table. You had an argument with me that I should dump X amount into my house which would take me 111 years to ROI and I told you that wasn't practical.
It still isn't.
Sure, it adds up when a few million people do it, but those other people aren't responsible for putting food on my table. You had an argument with me that I should dump X amount into my house which would take me 111 years to ROI and I told you that wasn't practical.
It still isn't.
ChrisJ
0
Re: lochinvar noble
What is the heat load? If it is close to the 110 output, then the Navian is way oversized.
That is the challenge with combo units, usually one or the other side is a compromise.
That is the challenge with combo units, usually one or the other side is a compromise.
hot_rod
2