Welcome! Here are the website rules, as well as some tips for using this forum.
Need to contact us? Visit https://heatinghelp.com/contact-us/.
Click here to Find a Contractor in your area.
If our community has helped you, please consider making a contribution to support this website. Thanks!
Best Of
Re: Very Cool 😎 Urinals at a Brewery
Hello @hot_rod,
I'm not saying the product complies with any of the needed codes or listings for that application. Just saying what they stated and they are out there for sale. So the ones that @Mad Dog_2 found may not be Home Brew...
I'm not saying the product complies with any of the needed codes or listings for that application. Just saying what they stated and they are out there for sale. So the ones that @Mad Dog_2 found may not be Home Brew...
109A_5
1
Re: Low Water in Boiler - Wet Steam Likely
You are still way under vented with those G1's. If you have 75' of main and return you need at least I Big Mouth or 2 G2's plus 1 or 2 of your G1's to properly vent your system.
Re: Burnham Independent Near-Boiler Piping - Seeking Advice
Going back to your first couple of pictures, what is going on at the ceiling? Near the sheetrock?
Is it possible the new main from the new boiler splits into two mains? Is there anywhere above that sheetrock where water could sit in the piping?
Is it possible the new main from the new boiler splits into two mains? Is there anywhere above that sheetrock where water could sit in the piping?
Shane_2
1
Re: Banging steam radiator
That is a notoriously fast vent. A slower one may help the radiator heat and produce condensate more slowly.
bburd
2
Re: Burnham Independent Near-Boiler Piping - Seeking Advice
@ethicalpaul
It sounds like it's coming from the radiator, as if the vent is spinning around. But I also know that the source of water hammer is not always where you hear it. Need to do more investigating.
Thanks for the callout. Re: water quality, I'm north of Boston in a town known for its hard water.
Edit: Photos attached.I'll add a photo when I'm back home but it's 0.5 psi with a 1 psi differential. I adjusted the cut-in earlier a few days ago after noticing it was between 0.5 and 1. 
Unfortunately I don't know how it was sized. We had it installed before I knew anything about steam... regrettably I didn't ask all the great questions Dan calls out in We Got Steam Heat!.
The radiator/convector pitch is important, but even more important is the pitch of the pipes supplying them. Can you localize where the banging is coming from? It can be difficult. Unless condensate can drain back to the boiler, it will remain in the pipes and cause banging and/or "killing" of steam to that area.
It sounds like it's coming from the radiator, as if the vent is spinning around. But I also know that the source of water hammer is not always where you hear it. Need to do more investigating.
What the Burnham engineer said to you is weird. Water/steam zig-zagging to the header or equalizer is not a concern I have. In fact, that additional travel serves to let water droplets separate from the steam better. Also, if your water quality is decent, basically no water will be coming up the supply anyway. If the water is good, the header is basically unused in its purpose to separate water from steam because there is no water getting in there.
Thanks for the callout. Re: water quality, I'm north of Boston in a town known for its hard water.
Do you know what pressure your system gets to? Can you supply a photo of your Pressuretrol so we can see the settings? You want it set to basically the minimum pressure.
Edit: Photos attached.
Related to above, how was the boiler sized? Did the installer calculate the total sq ft of radiation in your house? That is necessary to ensure a properly-sized boiler. Too big a boiler will result in it building pressure too fast and cycling on pressure, which makes some people want to increase the Pressuretrol setting. DON'T DO IT
Unfortunately I don't know how it was sized. We had it installed before I knew anything about steam... regrettably I didn't ask all the great questions Dan calls out in We Got Steam Heat!.
milesgem
2
Re: The case of the non heating steam system, this Friday's case
My best guess is that there was a steam radiator in the attic that had been disabled for years. When the boys moved up there, they reactivated the radiator (with the valve, or by re-installing a plugged vent, whichever).
But the supply pipe for that radiator was in the wall behind the thermostat, heating it prematurely.
But the supply pipe for that radiator was in the wall behind the thermostat, heating it prematurely.
Re: 2 Pressuretrol Cut-Ins and 1 Cut Out?
@holograham
You could probably convert that burner to LO-High fire. It's still going to cost a few bucks. You replace one of the gas valves with a two position Honeywell gas valve and hook the gas valve linkage to the air dampers.
There is a little more to it and the installer has to be competent with that burner. This would be cheaper that full modulation which in my opinion is a little overkill for a burner that size.
I was a Power Flame rep for 10 years now retired.
You could probably convert that burner to LO-High fire. It's still going to cost a few bucks. You replace one of the gas valves with a two position Honeywell gas valve and hook the gas valve linkage to the air dampers.
There is a little more to it and the installer has to be competent with that burner. This would be cheaper that full modulation which in my opinion is a little overkill for a burner that size.
I was a Power Flame rep for 10 years now retired.
Re: Looking for help in south central kansas
Mkflyy said:
Grundfos UPS26-99FC Is the second added pump between the return manifold and water heater the other pump after expansion tank is a a grundfos up 15-42. Today I completely took the system apart to make sure there wasn’t an obstruction or something. I am using a 1/2 hp cast iron inline pump to fill and purge the system. I went through and did every loop individually after to starting with just the system loop then doing each individual loop. At this point I’m not opposed to adding a boiler but they are very expensive. I obviously don’t know what I am doing to install it either. Sounds like I would want a primary and secondary loop and I have looked at several diagrams and I can’t make sense of it and how I would add one to my system. So the last thing I want to do is buy a $2500 boiler and still not be able to get it to work. I also don’t have natural gas or LP only electric. That’s why I opted for this system.
Regardless of what's wrong, it must be corrected. First is, it needs to be an electric boiler, not an on demand water heater.
Then simply follow the boiler manufacturer piping instructions, and you'll be good to go.
HVACNUT
1
Re: Are there seriously no leveling shims I can just buy?
Plastic checkers. You get to choose the color.
Re: 2 Pressuretrol Cut-Ins and 1 Cut Out?
A modulating burner would be wonderful. Unfortunately, your burner cannot really be retrofitted to modulate. In simple terms, Powerflame produces three type of gas power burner that would likely fit your boiler. On/off is what you have, low/high/low is the next step up and fully modulating is the top of the line version.
The advantage of low/high/low firing is there is a small flame at start, high fire until roughly 1psi steam pressure, and back to low fire until the call for heat is satisfied or the pressure goes above say 2psi. With modulating burners, the flame (in theory) stays on even longer and you get more even heating and less short cycling. Ideally, a modulating burner would allow the boiler water to "simmer" all day like the coal boilers did a hundred years ago. With modulating burners you need a special pressure control that sends a variable (modulating) signal to the burner. We don't talk specifics about pricing, but I would guess a special order modulating burner with controls would cost you more than double the cost of the existing burner.
The advantage of low/high/low firing is there is a small flame at start, high fire until roughly 1psi steam pressure, and back to low fire until the call for heat is satisfied or the pressure goes above say 2psi. With modulating burners, the flame (in theory) stays on even longer and you get more even heating and less short cycling. Ideally, a modulating burner would allow the boiler water to "simmer" all day like the coal boilers did a hundred years ago. With modulating burners you need a special pressure control that sends a variable (modulating) signal to the burner. We don't talk specifics about pricing, but I would guess a special order modulating burner with controls would cost you more than double the cost of the existing burner.
