Welcome! Here are the website rules, as well as some tips for using this forum.
Need to contact us? Visit https://heatinghelp.com/contact-us/.
Click here to Find a Contractor in your area.

Need advice on demoing an old cast iron boiler

bruceackman
bruceackman Member Posts: 2
edited October 23 in THE MAIN WALL

It's too big to get out of the basement in one piece. I think it's 8 sections. Maybe a chisel bit on a hammer drill to get the sections apart? The space is too small to swing a sledge hammer. Any better ideas?

Thanks

Comments

  • ethicalpaul
    ethicalpaul Member Posts: 6,572

    Pics?

    NJ Steam Homeowner.
    Free NJ and remote steam advice: https://heatinghelp.com/find-a-contractor/detail/new-jersey-steam-help/
    See my sight glass boiler videos: https://bit.ly/3sZW1el

  • EdTheHeaterMan
    EdTheHeaterMan Member Posts: 9,317

    First of all, is there asbestos insulation on the boiler. If it was installed before 1950 that is a good possibility. A picture would help

    If it is a newer model (1960s or newer) then there are most likely some kind of tie rods holding it together. Cut the tie rods with a sawsall or grinder. then use the chisel to separate each section.

    But you need to get the asbestos removed before you start any work that may let asbestos fly into the air.

    Edward Young Retired

    After you make that expensive repair and you still have the same problem, What will you check next?

    DCContrarian
  • EBEBRATT-Ed
    EBEBRATT-Ed Member Posts: 16,400

    Some steel wedges used to split firewood, or a cold chisel will work. You can cut the tie rods and take them out and replace them with a new threaded rod with nuts on the inside and use the nuts to push the sections apart.

    If the sections are too heavy to remove cut them with an angle grinder with a cutting disk (just cut part way through) then hit it with a sledge hammer and it will come apart where the cut is.

    Safety glasses/goggles and gloves are a must.

  • SlamDunk
    SlamDunk Member Posts: 1,664

    my sections were too heavy after separating. I only had seven ft head clearance. A sledgehammer( and knee pads) shattered them but it was a workout. Plus everything @EdTheHeaterMan and @EBEBRATT-Ed said. I think , in hindsight, that a large, rotary hammer would have helped.

  • mattmia2
    mattmia2 Member Posts: 10,855

    You're going to want hearing protection too, even with the hand tools but especially with a demolition hammer or air chisel.

    ethicalpaul
  • The Steam Whisperer
    The Steam Whisperer Member Posts: 1,249

    And wear eye protection too. Cast iron cast fracture like shrapnel. I always use a heavy tarp over the cast I am breaking to act as a shrapnel blanket.

    To learn more about this professional, click here to visit their ad in Find A Contractor.
    Mad Dog_2ethicalpaul
  • mattmia2
    mattmia2 Member Posts: 10,855

    A hepa respirator probably isn't a bad idea either for soot and asbestos you may have missed and various other materials you might stir up.

  • Mad Dog_2
    Mad Dog_2 Member Posts: 7,508
  • JUGHNE
    JUGHNE Member Posts: 11,268

    I have laid an old tire on the floor for the section to fall on as it came loose.

    Concerned about cracking/chipping concrete.

    ethicalpaul
  • DCContrarian
    DCContrarian Member Posts: 667

    If there is asbestos you're probably better off finding someone with the ability to remove it in a single piece.

  • Big Ed_4
    Big Ed_4 Member Posts: 3,012
    edited October 23

    The boiler needs to be cold . Cut the pinch rods and wedge the sections apart. This would be the easier way..

    They break up easy if you swing a 17# hammer .. Smaller ones just bounce off ….

    There was an error rendering this rich post.