Welcome! Here are the website rules, as well as some tips for using this forum.
Need to contact us? Visit https://heatinghelp.com/contact-us/.
Click here to Find a Contractor in your area.

Multi-Meters

Hi Guys,
Just wondering what you guys are using for multi meters right now. I need get 2 or 3 for the service trucks, would like something with a magnet for attaching to boilers, and something that reads micro-amps. Any help greatly appreciated!.

Welcome

It looks like you're new here. Sign in or register to get started.

Comments

  • SWEI
    SWEI Member Posts: 7,348
    I own a number higher-end Flukes, but if I were shopping new I'd probably look at the 116 for basic field tech use. They sell a combo kit with the 323 clamp meter -- definitely want that capability if your guys are doing compressor work.
    Steve Minnich
  • ratio
    ratio Member Posts: 4,076
    My daily meter today is a Fluke 376. I use a UEI microamp adapter for microamps, so I can easily unplug from the flame circuit without killing the burn. I also have on the truck a UEI 389 and a Fluke 116 that I use often.

    And then there are the specialty meters...I can quit any time, I swear!

    SWEI
  • lchmb
    lchmb Member Posts: 2,997
    auto ranging Fluke..cant go wrong...works excellent with newer tech's as well..
  • BobC
    BobC Member Posts: 5,525
    I used Flukes for most of my working life, I have 3ea 8060a's down in the basement and one model 77. You can't buy a better meter than a Fluke.

    I have mixed feelings about auto ranging meters. They are very handy but not as fast as a standard DVM where you set the range.

    Bob
    Smith G8-3 with EZ Gas @ 90,000 BTU, Single pipe steam
    Vaporstat with a 12oz cut-out and 4oz cut-in
    3PSI gauge
  • SWEI
    SWEI Member Posts: 7,348
    I loved my 8060A. The dB, Hz, and relative functions were unheard of in a portable meter at the time.
  • Steve Minnich
    Steve Minnich Member Posts: 2,868
    Simpson 260 w the rolltop. : )
    Steve Minnich
    SWEIChrisJ
  • EBEBRATT-Ed
    EBEBRATT-Ed Member Posts: 18,311
    Cant beat a Fluke 902. Also have an Amprobe meter nice meter but the autoranging drives me nuts, don't use it much
  • SWEI
    SWEI Member Posts: 7,348
  • BobC
    BobC Member Posts: 5,525
    @Stephen Minnich I have a 260 that was given me for my birthday when I was a freshman in HS. I have a rolltop case for the newer 270 but have to be careful with it because it's a bit fragile (made of breakalite).

    The Simpsons were always my favorite because you could switch polarity on ohms - a great way to check caps and chokes.

    Bob
    Smith G8-3 with EZ Gas @ 90,000 BTU, Single pipe steam
    Vaporstat with a 12oz cut-out and 4oz cut-in
    3PSI gauge
  • ChrisJ
    ChrisJ Member Posts: 16,871
    Still using my Fluke 179 and Simpson 260 7P.
    You're not going to go for a Simpson for the trucks, but the 179 is a nice meter.

    Single pipe 392sqft system with an EG-40 rated for 325sqft and it's silent and balanced at all times.

  • BobC
    BobC Member Posts: 5,525
    edited November 2016
    @ChrisJ I also have a Heathkit Triplett clone that has a really rugged case but lacks the ohms polarity switching. It has a taut band movement so it's rugged but I don't know if I'd want it bouncing around in the back of a service truck. I also have a FET AC VTVM version of that meter that is really a great meter.

    Bob
    Smith G8-3 with EZ Gas @ 90,000 BTU, Single pipe steam
    Vaporstat with a 12oz cut-out and 4oz cut-in
    3PSI gauge
  • ChrisJ
    ChrisJ Member Posts: 16,871
    edited November 2016
    If I was a tech that went from job site to job site, I'd probably want a Fluke scope, but that's me.

    There are times having a scope can make troubleshooting so much easier, or sometimes, even possible at all.

    The other problem is, I love buying tools. I'm also as much a Fluke fan as I am a Yellowjacket fan. Not sure if that's a good thing, probably not.

    Single pipe 392sqft system with an EG-40 rated for 325sqft and it's silent and balanced at all times.

    SWEI
  • BobC
    BobC Member Posts: 5,525
    I have two scopes on my workbench. One is a Tek 2230 100mhz storage scope, the other is a Hitachi 35mhz 2 channel analog scope.

    A scope can definitely give you more information. People don't realize you don't need 0.05% accuracy for most of the work you do on electronics but you really do want to see any noise that is sitting on that 5v supply.

    Bob
    Smith G8-3 with EZ Gas @ 90,000 BTU, Single pipe steam
    Vaporstat with a 12oz cut-out and 4oz cut-in
    3PSI gauge
  • hot_rod
    hot_rod Member Posts: 25,425
    I imagine most current meters are, but make sure it is a true RMS. You need that to read trial relay outputs accurately.

    A dual temperature attachment is also nice for troubleshooting hydronics.
    Bob "hot rod" Rohr
    trainer for Caleffi NA
    Living the hydronic dream
  • hvacfreak2
    hvacfreak2 Member Posts: 500
    I use the Fluke 902 for most general purpose work. I keep an 87 in the truck for the few times that go beyond the range of the 902. The new 902 does sampling and connects to a phone app. I was also looking at Flir meters at an electrical supplier I frequent , I may break down and get one in the near future.
    hvacfreak

    Mechanical Enthusiast

    Burnham MST 396 , 60 oz gauge , Tigerloop , Firomatic Check Valve , Mcdonnell Miller 67 lwco , Danfoss RA2k TRV's

    Easyio FG20 Controller

Welcome

It looks like you're new here. Sign in or register to get started.

Welcome

It looks like you're new here. Sign in or register to get started.