Welcome! Here are the website rules, as well as some tips for using this forum.
Need to contact us? Visit https://heatinghelp.com/contact-us/.
Click here to Find a Contractor in your area.

E.D.R. of convector

ben_18
ben_18 Member Posts: 70
I am trying to figure out if the boiler is the right size for the house. There are a couple of convectors in the system. They are like the ones found on page 101 in "We've got steam heat." What is the E.D.R. per inch of these convectors?
Burnham Independence IN8

Comments

  • DanHolohan
    DanHolohan Member, Moderator, Administrator Posts: 16,513
    That's a generic picture

    Lots of manufacturers made convectors that looked like that and the rating would depend on which one you have. Pictures would help.
    Retired and loving it.
  • ben_18
    ben_18 Member Posts: 70
    Heres the picture

    The convectors are built into the wall and can't be opened up. I guess the height of it could be measured buy putting a tape measure in through the top and bottom if that would help. Attached is a picture of it.
    Burnham Independence IN8
  • DanHolohan
    DanHolohan Member, Moderator, Administrator Posts: 16,513
    Ouch.

    These always shrug their muscles and give one the hairy eyeball. Without knowing what sort of element is hiding back there it's just guessing.



    Anyone else want to wade in here?
    Retired and loving it.
  • Danny Scully
    Danny Scully Member Posts: 1,416
    edited May 2013
    Can we?

    Can we consider that a hidden radiator Dan?! Hehe, that grill looks like it can be removed. Similarly, the opening at the floor seems somewhat accessible. I would remove the grill, measure the length/depth of element, then probe from the bottom and top to see if you can get an idea of the height. I would do this on 1 radiator and use as a template, so to speak, for the rest.
  • DanHolohan
    DanHolohan Member, Moderator, Administrator Posts: 16,513
    You would, Danny.

    But I don't know our guest's abilities when it comes to probing into walls. A lot went into the design of those things.
    Retired and loving it.
  • DanHolohan
    DanHolohan Member, Moderator, Administrator Posts: 16,513
    You would, Danny.

    But I don't know our guest's abilities when it comes to probing into walls. A lot went into the design of those things.
    Retired and loving it.
  • ben_18
    ben_18 Member Posts: 70
    I would take

    the cover off but it is covered by sheet rock and I don't want to ruin the paint.

    I guess the bottom could be taken off. I have taken off the cover and looked inside. Here's a picture-
    Burnham Independence IN8
  • Steamhead
    Steamhead Member Posts: 16,796
    Here are two sources

    which you can find right here in the Library. Yes, it really does pay to wander off the Wall:



    http://www.heatinghelp.com/article/158/Radiators/1269/Herman-Nelson-Invisible-Radiators



    http://www.heatinghelp.com/article/158/Radiators/1280/Trane-Heat-Cabinets



    Now, how did I know these could be found there?  ;-)
    All Steamed Up, Inc.
    Towson, MD, USA
    Steam, Vapor & Hot-Water Heating Specialists
    Oil & Gas Burner Service
    Consulting
  • ben_18
    ben_18 Member Posts: 70
    Looks good

    Thanks! I have my work cut out for me.
    Burnham Independence IN8
  • SWEI
    SWEI Member Posts: 7,356
    While you're at it

    See if you can slip a vacuum hose down there and clean those fins.
This discussion has been closed.