Threading on glass gauge nuts? (or are sight-glass related specs a secret?...)
Been doing my own steam-boiler sight-glass cleaning/replacement for years. Just helped a neighbor do it for the first time. We both have 5/8ths glass.
Making conversation, he asked, "so what kind of threading is on these things" (the glass gauge nuts). Other than that it's "standard" - never thought about it. And even though I know it doesn't matter, unfortunately now I'm curious.
My best-est web-search terms couldn't find anything. A couple of tries at online customer service of suppliers accessible to non-professionals, only got back "it's standard."
With my bad eyes, looks like near to ~20 TPI, with a ruler near to ~7/8" - and since it uses a gasket, may be straight thread...?
It would be too much of a coincidence if it turned out to be the kitchen-faucet aerator "standard" (which one website said is 15/16"M 55/64"F -20 UN thread). But would guess it's at least close.
Thanks.
Comments
-
I don't know what thread it is but it's one of those "who cares" thing. They are all the same as far as I know unless you get on high pressure steam.
Google: Ernst instruments
1 -
us a micrometer or a caliper. use a magnifying glass and measure several threads and divide for the pitch. what profile are they?
0 -
I believe it is the same thread as most other 5/8” compression fittings. It uses a rubber ring instead of the brass ferrule, on glass tube
Bob "hot rod" Rohr
trainer for Caleffi NA
Living the hydronic dream
1 -
Thanks for giving it a shot. I have no experience with this sort of thing (determining TPI and pitch etc.), and don't have the tools to get a precise measurement. Couldn't quickly find the specs for other compression fittings, as reasonable suggested.
I'll just have to try to sleep at night : )
0 -
Never pondered it, but there are so many different thread patterns we work with. Mad Dog
0 -
Including 100% custom ones.
Single pipe 392sqft system with an EG-40 rated for 325sqft and it's silent and balanced at all times.
0 -
Super Dooper tap and die kit should have a thread guage in it. Kind of like a set of feeler guages but they have little teeth that nest into the threads to tell you what the pitch is.
0 -
Kinda like this
Single pipe 392sqft system with an EG-40 rated for 325sqft and it's silent and balanced at all times.
0 -
ChrisJ said: Kinda like this. [photo]
Whoa. That's a beautiful vintage tool. Wish things were still made like that.
Seeing that Made-In-USA gauge inspired me to give it one last web-try before shutting-down, and I'll be darned. Found something in the Q&A for a 5/8" glass Conbraco nut at MSCDirect:
Q. Asked by Ethan 5 years ago: What is the inside threading of this nut?
A. Staff Expert - Rob: The thread size on this nut is 15/16-18 tpi1 -
-
mattmia2 said: link to Gauge Set at Grainger
Made me smile. I was picturing something more like an $8.99 set at Amazon…
0 -
it looks like general only makes the style like i have now that is like a set of feeler gauges but hinged at both ends with different ranges at each end but starrett still makes the triangular style
0 -
I’m very curious about the sketch on the reverse side on the paper in the picture. 😂
0 -
I think it was a very crude fast drawing of a check valve and pressure relief.
Single pipe 392sqft system with an EG-40 rated for 325sqft and it's silent and balanced at all times.
1
Categories
- All Categories
- 86.4K THE MAIN WALL
- 3.1K A-C, Heat Pumps & Refrigeration
- 50 Biomass
- 419 Carbon Monoxide Awareness
- 91 Chimneys & Flues
- 2K Domestic Hot Water
- 5.4K Gas Heating
- 93 Geothermal
- 156 Indoor-Air Quality
- 3.4K Oil Heating
- 59 Pipe Deterioration
- 921 Plumbing
- 6.1K Radiant Heating
- 374 Solar
- 15K Strictly Steam
- 3.3K Thermostats and Controls
- 50 Water Quality
- 40 Industry Classes
- 47 Job Opportunities
- 17 Recall Announcements