Welcome! Here are the website rules, as well as some tips for using this forum.
Need to contact us? Visit https://heatinghelp.com/contact-us/.
Click here to Find a Contractor in your area.

Curved Radiator

The first one I've seen on my route. One hundred year old house in the Berkeley Hills. The boiler, radiators and piping are untouched.
8.33 lbs./gal. x 60 min./hr. x 20°ΔT = 10,000 BTU's/hour

Two btu per sq ft for degree difference for a slab
HillykcoppChrisJ

Comments

  • STEVEusaPA
    STEVEusaPA Member Posts: 6,506
    Beautiful rads, served by a snowman!
    steve
  • ChrisJ
    ChrisJ Member Posts: 15,583
    I thought snowmen were round and tall?
    Single pipe quasi-vapor system. Typical operating pressure 0.14 - 0.43 oz. EcoSteam ES-20 Advanced Control for Residential Steam boilers. Rectorseal Steamaster water treatment
  • HVACNUT
    HVACNUT Member Posts: 5,804
    That's really cool!
    The interior designers must have had there hands full the the original owner.
    And pay no attention to the white blanket no matter how cuddly it looks.
  • I particularly liked the thermometer.
    8.33 lbs./gal. x 60 min./hr. x 20°ΔT = 10,000 BTU's/hour

    Two btu per sq ft for degree difference for a slab
    HillykcoppChrisJ
  • Steamhead
    Steamhead Member Posts: 16,796
    That's an Italian Flue radiator. Probably the first curved one I've seen of that type. A classic!
    All Steamed Up, Inc.
    Towson, MD, USA
    Steam, Vapor & Hot-Water Heating Specialists
    Oil & Gas Burner Service
    Consulting
    Turbo Dave
  • DanHolohan
    DanHolohan Member, Moderator, Administrator Posts: 16,513
    Beautiful! Thanks for sharing, Alan.
    Retired and loving it.
  • newagedawn
    newagedawn Member Posts: 586
    nice piece of history there, very cool
    "The bitter taste of a poor install lasts far longer than the JOY of the lowest price"
  • Henry
    Henry Member Posts: 998
    I have seen curved radiators here in the wealthy areas. Do you have any idea what make boiler that is?
  • Steamhead
    Steamhead Member Posts: 16,796
    Bryant. Says so on the thermometer. Might be one of their first model series.
    All Steamed Up, Inc.
    Towson, MD, USA
    Steam, Vapor & Hot-Water Heating Specialists
    Oil & Gas Burner Service
    Consulting
  • The owner wants to upgrade his boiler. My first thought is to replace it with a Viessmann Vitocrossal CU3A with a sidearm water heater, replacing all the radiator valves with TRV's.
    8.33 lbs./gal. x 60 min./hr. x 20°ΔT = 10,000 BTU's/hour

    Two btu per sq ft for degree difference for a slab
  • HVACNUT
    HVACNUT Member Posts: 5,804
    > @Steamhead said:
    > Bryant. Says so on the thermometer. Might be one of their first model series.
    >
    >
    >> Alan said it's probably about 100 years old, but was Bryant on their own, or were they a subsidiary of that other company? You know, that company that touted it was gonna save American jobs, but went to Mexico anyway. The one where that guy stood in front of the corporate logo, and promised. That company.
  • Fred
    Fred Member Posts: 8,542
    Beautiful !!! If it were my house, I'd not change a thing. The history there would be worth more, to me, than any improvement in efficiency.
  • EBEBRATT-Ed
    EBEBRATT-Ed Member Posts: 15,452
    Ah, the old days!! A low voltage limit aquastat, a thermostat, no low water cutoff and a diaphragm gas valve.

    Life was good!! What do we need modern controls and circuit boards for anyhow??
  • HVACNUT
    HVACNUT Member Posts: 5,804
    > @Fred said:
    > Beautiful !!! If it were my house, I'd not change a thing. The history there would be worth more, to me, than any improvement in efficiency.
    >
    >
    >> I'd do the same, except for the boiler. That would scare the crap out of me. I'd convert to oil. Lol.
    That is asbestos right?
  • Steamhead
    Steamhead Member Posts: 16,796
    HVACNUT said:

    > @Steamhead said:

    > Bryant. Says so on the thermometer. Might be one of their first model series.

    >

    >

    >> Alan said it's probably about 100 years old, but was Bryant on their own, or were they a subsidiary of that other company? You know, that company that touted it was gonna save American jobs, but went to Mexico anyway. The one where that guy stood in front of the corporate logo, and promised. That company.

    Long, long ago, in what seems like a galaxy far away these days.......

    Bryant didn't get gobbled up until sometime in the last couple decades or so.
    All Steamed Up, Inc.
    Towson, MD, USA
    Steam, Vapor & Hot-Water Heating Specialists
    Oil & Gas Burner Service
    Consulting
  • Fred
    Fred Member Posts: 8,542
    @HVACNUT , yep, that is asbestos but it is intact and looks like it's in great shape.
  • flat_twin
    flat_twin Member Posts: 350
    Do you suppose they built that radiator on site? Would the egg shape of the push nipples be enough to allow that curve? Secured with curved rods too?
  • unclejohn
    unclejohn Member Posts: 1,833
    I would fer sure get rid of that gas valve and cock err shut off valve. Also I would paint a big skull and under it a wrench and hammer.
  • Fred
    Fred Member Posts: 8,542
    I agree with @unclejohn . I would get rid of that old gas valve and the shut off valve (they always tend to leak a bit around the stem but I'd keep the boiler.
    @flat_twin , that radiator looks like it has 5 or 6 straight sections on each end and only the center 3 or four center sections are curved. Maybe they had curved nipples for that center section and the rods only had to be bent in the center??