Welcome! Here are the website rules, as well as some tips for using this forum.
Need to contact us? Visit https://heatinghelp.com/contact-us/.
Click here to Find a Contractor in your area.
Multicore fastening
singh
Member Posts: 866
My rems akku-press accepts multi cor head.
Head should work with Ridgid also.
<A HREF="http://www.heatinghelp.com/getListed.cfm?id=377&Step=30">To Learn More About This Professional, Click Here to Visit Their Ad in "Find A Professional"</A>
Head should work with Ridgid also.
<A HREF="http://www.heatinghelp.com/getListed.cfm?id=377&Step=30">To Learn More About This Professional, Click Here to Visit Their Ad in "Find A Professional"</A>
0
Comments
-
What's the latest in
Multicore fastening. Can I use multicore jaws with my propress somehow? I'd hate to buy a whole new tool for fastening, but I'm using multicore a lot for radiator piping, and radiant floors, and doing it by hand is a lot of work. I'd like to speed things up if it's not too expensive. WW
To Learn More About This Professional, Click Here to Visit Their Ad in "Find A Professional"0 -
What do you mean ?
> Multicore fastening. Can I use multicore jaws
> with my propress somehow? I'd hate to buy a
> whole new tool for fastening, but I'm using
> multicore a lot for radiator piping, and radiant
> floors, and doing it by hand is a lot of work.
> I'd like to speed things up if it's not too
> expensive. WW
>
> _A
> HREF="http://www.heatinghelp.com/getListed.cfm?id=
> 255&Step=30"_To Learn More About This
> Professional, Click Here to Visit Their Ad in
> "Find A Professional"_/A_
0 -
What do you mean ?
"by hand" ?
I use a hand press for 1/2 and 5/8. It won't handle bigger, but usually don't get a need for much bigger. It's quick enough for me, a whole lot better than compression.0 -
I'm dealing with 3/4 inch
today, and I'm fighting tendonitis in my right forearm, so I'd rather power up. WW
To Learn More About This Professional, Click Here to Visit Their Ad in "Find A Professional"0 -
wayne...
I just borrowed one to do some work w/ MC...it had heads for 1/2", 5/8" , 3/4" and 1"...I know HR has done it in 1 1/4"....rems should have the heads....kpc
To Learn More About This Professional, Click Here to Visit Their Ad in "Find A Professional"0 -
All of REMS heads.........
fit the ProPress machine (except the small cordless). The all thread cutter head is a useful tool, also. I have been using Multicor (mostly 3/4") for my supply and return piping since pricing of copper went stupid. I don't think I'll ever use copper again for any S&R piping of remote equipment (manifolds, air handlers, etc.).There was an error rendering this rich post.
0 -
Where do I
get the REMS heads.?? WW
To Learn More About This Professional, Click Here to Visit Their Ad in "Find A Professional"0 -
-
Ferguson had my REMS jaws in stock.....in Soldotna, Alaska no less. Had it in Seattle in a couple days.0 -
uponor
you can get the head from uponor, thru your supplier.
To Learn More About This Professional, Click Here to Visit Their Ad in "Find A Professional"0
This discussion has been closed.
Categories
- All Categories
- 86.3K THE MAIN WALL
- 3.1K A-C, Heat Pumps & Refrigeration
- 53 Biomass
- 422 Carbon Monoxide Awareness
- 90 Chimneys & Flues
- 2K Domestic Hot Water
- 5.4K Gas Heating
- 100 Geothermal
- 156 Indoor-Air Quality
- 3.4K Oil Heating
- 63 Pipe Deterioration
- 917 Plumbing
- 6.1K Radiant Heating
- 381 Solar
- 14.9K Strictly Steam
- 3.3K Thermostats and Controls
- 54 Water Quality
- 41 Industry Classes
- 47 Job Opportunities
- 17 Recall Announcements