Click here to Find a Contractor in your area.
Welcome! Here are the website rules, as well as some tips for using this forum.

If you've found help here, check back in to let us know how everything worked out.
It's a great way to thank those who helped you.
Need to contact us? Visit https://heatinghelp.com/contact-us/.

How To Straighten Bent Ball Valve Handle

D107D107 Member Posts: 1,686
edited August 2 in Plumbing
Had a new water main put in last year. Installer put two ball valves in, one close to where pipe enters house (main valve) and a backup one after the meter. He intentionally bent the handle probably to allow initial threaded installation, but recently another plumber came for other work and found he couldn't use the secondary valve since the bent handle would have hit the line. I had thought using two sets of pliars--one as an anchor and the other to bend might easily work, but there's a risk of stressing the pipe. I also wondered if that nut could be loosened without affecting the valve so I could remove the handle, re-bend then put back. But don't know if loosening nut also loosens valve itself. I paid for the extra valve so want it to work; could easily call back original installer if need be.

metrorental

Comments

  • ChrisJChrisJ Member Posts: 11,073
    I just did the same work at my house and most places the extra valve isn't extra, it's required to allow easy replacement of the meter.

    The nut comes off and then the handle can be removed.  Sometimes you may need to rock the handle a little.

    I'm confused as to why he bent the handle instead of just removing it like most would do.  The handle can also be flipped to swing different.
    Single pipe quasi-vapor system. Typical operating pressure 0.14 - 0.43 oz. EcoSteam ES-20 Advanced Control for Residential Steam boilers. Rectorseal Steamaster water treatment
    D107STEVEusaPA
  • HVACNUTHVACNUT Member Posts: 3,414
    Hold the valve while loosening the nut. Pop the handle off and flip it to turn the valve on/off. I see this "whoops" a lot. Some bend the handle, some cut some length off it. Most learn for next time. Some don't. 
    D107
  • ChrisJChrisJ Member Posts: 11,073
    @D107. Just out of curiosity can you take a picture further back showing the rest of the work?
    Single pipe quasi-vapor system. Typical operating pressure 0.14 - 0.43 oz. EcoSteam ES-20 Advanced Control for Residential Steam boilers. Rectorseal Steamaster water treatment
  • D107D107 Member Posts: 1,686
    edited August 1
    Thanks all. @ChrisJ From right to left (house side towards street); first you'll see shot of old working gate valve that can be used to keep house water up in the pipes when working on something below; then original post showing bent handle, then meter, then after meter and incoming line. There is a hard-to-see ball valve at the incoming wall. I'd wanted a caleffi PRV and pressure gauges before and after meter but contractor was old school didn't want those bells and whistles.

    I took off the top nut and tried to flip it two ways, over and also tried putting handle on the left, but first way the stop no longer is in correct position so valve could keep turning and turning. handle is HARD to bend back.







  • D107D107 Member Posts: 1,686
    edited August 1
    Having looked at this, the real problem is that the way it is now, the handle will hit the pipe on its way to off; if I straighten the handle, it will hit the wood support. If I flip handle to the left, it will hit the PRV to valve's left. I think I have to get the installer back to turn the whole valve more. Or can I just buy a short valve handle? Since existing handle looks like brass guess I'll have to get like material.


  • GroundUpGroundUp Member Posts: 993
    Handles are bent like that every day. I've done it myself hundreds of times and the insulators do it to almost every one they touch. There's no harm in letting your instincts take over and just bend it back to straight. If it's too long, cut the handle off.
    D107
  • hot_rodhot_rod Member Posts: 13,519
    How often will you use it?
    Remove the handle and use a small crescent or open end wrench to turn it, when needed.
    The shorty handles can be hard to turn by hand if they are not exercised occasionally.
    Cut it down like @GroundUp mentioned slip a piece of heat shrink tube over it and mold a new handle.
    Bob "hot rod" Rohr
    trainer for Caleffi NA
    The magic is in hydronics, and hydronics is in me
    D107
  • ChrisJChrisJ Member Posts: 11,073
    If it makes you feel any better I have a ball valve on my wet return on my steam system.   It's by the floor in a bad spot which I regret putting it but since 2011 my self and a few others have kicked it and tripped over it.  The handle has been bent several times on the valve and it's still fine.



    Single pipe quasi-vapor system. Typical operating pressure 0.14 - 0.43 oz. EcoSteam ES-20 Advanced Control for Residential Steam boilers. Rectorseal Steamaster water treatment
    D107
  • D107D107 Member Posts: 1,686
    @ChrisJ yes, I always come out of Wall threads learning a bit more, though in the scheme of things this is no biggie. I did notice when I first flipped it in such a way that it was without the stops the valve kept turning, and one wouldn't know how open or closed it was unless you tested it with a faucet. Luckily I reversed my motion and got back to default as far as I know.

    Another takeaway is the reminder to exercise my heating system and domestic system valves once a year or so.

    With the new water main, metal particles no longer collect in the bottom of the toilets.
  • mattmia2mattmia2 Member Posts: 1,438
    the flats on the stem are in parallel with the hole in the ball
    D107GroundUpCanucker
  • george_42george_42 Member Posts: 86
    when you work in the trade a bent handle is the least of your problems
    DanHolohan
  • JUGHNEJUGHNE Member Posts: 6,981
    I have had this problem a couple of times.
    First you can straighten the handle in place,
    then slip the plastic cover off the handle, maybe heat with hair dryer.
    Remove the handle with that nut.
    Cut the handle short enough with a bolt cutters or hack saw, in a vice.
    Then I would round the corners on a grinder wheel to match the part cut off, shorten the plastic sleeve with scissors as needed and slip back on.
    A short piece of PVC pipe gives you a handle extension for that first hard movement, after that no problem.
    Or a crescent wrench on the handle at the nut end.
    D107
  • Jamie HallJamie Hall Member Posts: 12,952
    I've done that a few times, @JUGHNE . I like to put at least a stub of the handle back on, so i can see at a glance whether the dang thing is open or closed...
    Br. Jamie, osb

    Building superintendent/caretaker, 7200 sq. ft. historic house museum with dependencies in New England.

    Hoffman Equipped System (all original except boiler), Weil-Mclain 580, 2.75 gph Carlin, Vapourstat 0.5 -- 6.0 ounces per square inch
Sign In or Register to comment.

Welcome

It looks like you're new here. If you want to get involved, click one of these buttons!